Internal Linings  Wet Area Products
 
 

DUROMASTIC ACS is a liquid applied membrane which when reinforced and fully cured forms a flexible waterproof lining for showers and other wet areas as described in Australian Standard AS3740 -1994 -"Waterproofing wet areas within residential buildings. "

DUROMASTIC ACS forms a waterproof lining to most materials used for building construction including reinforced concrete, cement render; water resistant plaster board, fibre reinforced cement sheets, particle board flooring and plywood etc. The surface must be firmly fixed to manufacturer's directions free of protrusions, dirt, oil and dry

COVERAGE

Floors, hobs and upturns, use 1.5 to 1.8 litres/m2, depending on the surface texture to give a minimum dry film thickness of 0.8mm. Walls, use 0.3 to 0.5 litres/m2.

PRECAUTIONS

Do not apply above 32C or below 8. Wash equipment with water before dry. Do not fix tiles until fully dry, normally 1 -4 days. Areas subject to rising damp should be first sealed with an epoxy coating, ie. DUROMASTIC WBE. Protect membrane against damage before and during tiling. Tile over external compressed fibro within 4 weeks. When tiling over external membrance surfaces ensure full allowance is made for expansion and contraction which may damage the membrane.

PACKAGING

DUROMASTIC ACS is available in 20, 10, and 4 litre pails, or in kits with fibreglass. Fibreglass and polyester reinforcements are available in 1 m and 150mm wide lengths

GENERAL

Shelf life 2 years in sealed container
Touch Dry 2-4 hours
Colour Gray or White
Thinning Water
Toxicity Non Toxic
Solvent Resistance Not Resistant
Weather Resistance Very Good
Elongation 160%
Moisture Vapour Transfer 0.45g/h-m2

 

DUROMASTIC ACSFIBRE

 

DUROMASTIC ACS Fibre is a liquid applied co-polymer membrane containing a fibrous filament reinforcing. When fully cured DUROMASTIC ACS Fibre forms a flexible waterproof lining for showers and other wet areas as described in Australian Standard AS 3740-1994 "Waterproofing Wet areas within residential buildings".

DUROMAST1C ACS Fibre forms a waterproof lining to most building materials including reinforced concrete, cement render; water resistant plasterboard and fibre reinforced cement sheet flooring etc. The surface must be firmly fixed to manufacturers directions, clean find dry.

DUROMASTIC ACS Fibre is suitable as an externally exposed waterproof membrane on decks, parapets, balconies- and flashings.

PRINCIPLE CHARACTERISTICS

  • Simple application - single pack, water based.
  • Fast curing
  • Reinforcement free application
  • Good flexibility
  • Seamless, no joints or cracks
  • Low odour

USE AREAS

  • Shower tray and wet areas
  • Deck and balconies
  • Tanking
  • Retaining walls

PACKAGING

Duromartic ACS Fibre is available in 15 Litre and 4 Litre containers.

GENERAL

Coverage

1.8 litres / m / 1.2mm

Shelf life

2 years in sealed container

Touch Dry

2-4 hours

Colour

Off White

Thinning

Water

Toxicity

Non Toxic

Solvent Resistance

Not Resistant

Weather Resistance

Very Good

PRECAUTIONS

All sheet flooring must be fixed to the manufacturers directions before membrane is applied. Do not apply above 35C or below 8C ambient. Ensure coating is fully dry before contact with water or tiling, assist drying with air movement if necessary. Wash equipment with water before dry. Protect membrane against damage when tiling. Externally, provide a slip sheet between membrane and topping and allow sufficient expansion and contraction control joints in overlaying tiles and topping particularly important with sheet flooring externally, or damage to the membrane may occur. External decks shall be properly drained.

CLEAN UP

Clean up with fresh water before dry



  Home | Internal Linings | External Linings | Handyman Tips
Download | Request Free Quote | Completed Project | Contact Us

Copyright 2005 © I&V Plaster Maintained by Solutions2web